![]() Oh and I killed the trackerd process at the gnome system monitor and nothing. move ubuntu disk to another laptop I have Ubuntu 22.04 installed on my Dell XPC 13 9350, VGA compatible controller: Intel Corporation Iris Graphics 540 (rev 0a), Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter (rev 32), Qualcomm Atheros QCA6174 802. Now it even made the system a little slower, wich I notice when watching hdtv videos. The light keeps blinking even without connecting to internet. Then I thougt it might be the HD that someway was indexing files, so I let the computer on all night on the gdm, without starting any session. Then I remember that I was skipping the hd scaning at the system loading, so last night I let the computer make it, and nothing Then I thought it could be some process using lots of CPU and therefore accessing more often to the HD, but both CPUs are around 8% usage, and the process that use more memory is at the moment the gnome system monitor. ![]() When I first noticed this I checked the gnome-system-monitor if it was using an excesive amount of RAM and begining to use the swap, but i was using only 350 MB RAM with Firefox and Compiz fusion working. I've googled it and some other people had the same problem as well, but no solutions at all. If this is not enough, you may have to resort to a diagnostic tool, like smartctl.Two days ago I made the routine system update trough Synaptic and til now the HD light wont stop blinking all the time with apparently no reason. Notice that this does not scan your system, but simply reports what the BIOS says your pc is like. Or you can use dmidecode (not available on more recent versions of Linux) which allows you access to your hardware as seen in the BIOS (or, more exactly, in the SMBIOS, System Management BIOS). Or you can query general information about the disk by means of lshw -C disk ( sudo is important, if you omit it you will only display the user journal, not the kernel's). Opening the Disks utility Inside this menu, select the disk that you wish to configure, and then open up the drive settings menu. Sábados de 9.30 a 13 Hs Local a la calle ubicado en PalermoFS ComputersNueva Laptop Vospara pequeñas empresasAmplifique su rutina de trabajo. Unless of course you are on systemd, in which case the above command still works, but you can display the kernel messages as follows: sudo journalctl | grep sda FS ComputersLas Mejores Marcas al mejor PrecioEstamos de Lunes a Viernes de 9.30 a 13:00 Hs y de 14:00 a 18:30 Hs. dmesg displays the messages stored in /var/log/dmesg. If instead you want messages, including error messages, produced in the current session, then dmesg | grep sda If you want to take a look at your MBR ( if you have one), then dd if=/dev/sda of=mbr.bin bs=512 count=1 If the LED doesn't blink even during the boot-up (when the HDD is initially read) then it should be what I said. So this should be a problem with your hardware, regardless of what OS you are using. If you want the partition table, parted /dev/sdaĪnd the p (for print) will show you the partition table. As far as I know, blinking of HDD-LED on accessing HDD is an OS-independent hardware function. The proper way is to use udevadm info -a -n /dev/sda It depends on the kind of information you are searching for. My syslog says there is something wrong with my ata2, however, because Linux/Ubuntu swap disk orders all the times, I want to know exactly which of my 3 drives is ata2. Started Tell Plymouth To Write Out Runtime Data. Starting Tell Plymouth To Write Out Runtime Data. Ls: cannot access /var/log/me*: No such file or directory ![]() ![]() Ls: cannot access /var/run/dmesg*: No such file or directory Ls: cannot access /var/run/dmesg.boot: No such file or directory % ls /var/run/dmesg.boot || echo no found But under my Ubuntu I have none of them: # Run as root, The Linux Command To Find SATA says to check a log file called /var/log/messages. ![]() The FreeBSD Find Out All Installed Hard Disk Information says to check the /var/run/dmesg.boot file. In conclusion, we have discussed how to install GNOME Disks in Ubuntu 22.04 release. Thereafter, we can now launch the GNOME Disks from our Systems main menu. Stacer offers complete control to the user for changing the system accordingly. Hence, open a terminal and issue the following. This GUI tool is written in C++ and majorly focuses on removing unnecessary files and cache of the system. I know normally the Hard Disk Information can be get from dmesg, on fresh reboot, but my system has only been up for 15 days, and I've already lost that info. Stacer is a fantastic tool that can optimize your storage by managing the different aspects of your operating system. What's the reliable way to find out Hard Disk Information under Ubuntu, after having been booted for several days? $ uptimeĢ1:18:59 up 15 days, 10:46, 11 users, load average: 1.01, 0.82, 0.65 ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |